How To Fix A Lazy Susan Cabinet Door

Download Article

Adjusting misaligned Lazy Susan units might seem intimidating, only the virtually common corrections you'll demand to make can be done at habitation using standard tools. Set up rotation issues by adjusting the center shaft or bottom shelf position. Remedy misaligned doors by correcting the door position from within the overall unit.

1
Pinpoint where rotation bug are occurring. When a Lazy Susan becomes potent and difficult to rotate, the trouble is usually caused past either the middle shaft or the position of its lesser shelf. Lightly spin the Susan and annotation where it locks up, has difficulty turning, or has poor clearance.^[1]
- If the center movable shelf begins to bind, information technology will prevent free rotation. In this situation, you'll need to loosen this shelf.
- If the circular shelves sideslip downwards the center shaft, the bottom shelf tin can begin to drag, making it difficult to turn. You will need to accommodate the tiptop of this shelf to fix the problem.
2
Locate the locking bolt to adjust the center shaft. Look at the top of the center shaft. In that location should be one big commodities locking the exterior shaft to a metal sleeve positioned inside the shaft. This is the locking bolt for the shaft.^[2]
- This bolt holds the center shaft in place and maintains the length of the shaft. Sometimes excess pressure from this bolt tin can cause the shaft to bind.
- On some models, the locking commodities might be located at the bottom of the Susan, still, in almost cases, it volition establish near the summit.
Advertisement
three
Loosen the bolt. If anything is inside your Lazy Susan, empty it then you have more than space to work. Using a wrench or ratchet, loosen the bolt past turning it i-quarter of a full rotation counterclockwise. At get-go, the bolt may require some elbow grease to break loose.
- Only loosen the bolt plenty to manipulate the hardware within the center shaft. On some models, this might require more or less than one-quarter rotation.
- Generally, it's better to loosen the bolt in pocket-sized increments. This will prevent y'all from loosening it too much, which could result in the alignment of the Susan being thrown off.
4
Motility the adjusting rod. Now that the bolt is loose, y'all'll exist able to adapt the center shaft. Slide the metal adjusting sleeve the bolt was property in place no more than than i inch (ii.5 cm) to provide better clearance betwixt the eye shaft and peak of the cabinet.^[3]
- Work in small increments when adjusting the centre shaft. Large adjustments could crusade the Lazy Susan to topple over.
five

Tighten the bolt to finish adjusting the center shaft. Utilise your wrench or ratchet to carefully refasten the locking commodities in identify. Exercise not over-tighten the bolt. It should be looser than it was initially, but still tight enough to concur the adjusting rod in place.^[4]
half dozen
Locate the locking screws to adjust the shelf position. Most Lazy Susans should have two or more than locking screws located at the center of each shelf. These screws hold the shelves to the middle shaft.
- When all of the shelves are held together by the front decorative panel, you will need to adjust the unabridged shelf system. In this instance, there may not exist screws located at the top of each shelf.
- If the shelves must be adjusted separately, you'll only need to work with the bottom shelf. Locate the locking screws in the bottom shelf simply.
7
Loosen the screws. Loosen the locking screws using a Phillips-head screwdriver or similar tool. Hold the screwdriver so its head meets the fastener straight on. Apply firm force per unit area downward on the screw while turning counterclockwise to prevent stripping fastener hardware.^[v]
- Screws can be left in their holes once they accept been unattached from the center shaft. Nevertheless, you may desire to set loosened screws off to the side to preclude any from getting lost.
viii
Enhance the shelves to finish adjusting shelf position. Carefully lift the bottom shelf or entire shelf organisation until there is roughly half an inch (i.25 cm) of space betwixt the bottom shelf and the bottom of the cabinet.
- The shelves may resist this aligning and brainstorm binding on the centre shaft. Maneuver shelves until they are level and at a suitable height.
- Under no circumstances should yous lubricate the middle shaft. Doing so could preclude the screws from holding their position.
9
Tighten the screws. Concord the shelf in place with one hand and employ your complimentary hand to tighten the locking screws back in place with a screwdriver. Accept care not to let the shelf slip as you reattach fasteners, as this could cause it to become uneven or bounden.^[6]
- Brand the screws as tight every bit possible without stripping any of the hardware. The shelves must be stationary and secure to prevent this kind of misalignment.

1
Locate where there are door issues. Door issues are usually easier to identify than rotation problems. The door of the unit of measurement may close unevenly or information technology may not have sufficient clearance at the top, bottom, or sides of the chiffonier.
- If the door does not shut completely, or if it closes unevenly, you'll need to arrange the doors until they are centered correctly within the frame.
- When the top or lesser clearance is insufficient, you'll notice the gaps at both sides of the door will be diff.
- When the side clearance is insufficient, the door will appear crooked. Additionally, the gaps around information technology volition only unequal.
ii
Loosen the neckband screw when doors shut unevenly. Open up the door and locate the collar at the tiptop of the unit. For many models, this part volition be made of white plastic. Use a Phillips-head screwdriver to loosen the screw on this neckband.
- Loosen the screw by one full counterclockwise rotation. Even loosened, the screw should remain in its position in the collar.
3
Rotate the shelf unit and door counterclockwise. Using both hands, carefully rotate the entire shelf unit of measurement and door in a counterclockwise direction. Continue until the collar hits the catch latch located at the dorsum of the ceiling bracket.^[7]
- Plow the Lazy Susan slowly. Listen for a slight click. This is a signal that you've reached the grab latch.
- Once you striking the catch latch, the collar should exist properly aligned with the bound. You lot should feel a slight resistance to boosted counterclockwise turning.
4
Rotate the door. Gradually rotate the door in a clockwise direction until it reaches the exact eye-forepart. If possible, accept a step back and check the alignment from a distance. Brand sure the door is precisely in place earlier moving on.
- The plastic collar should remain stock-still in place as you rotate the door, so it may be hard to step away. Take a friend or family member assistance yous evaluate the door position, in these cases.
- If you accidentally rotate by the center-front position, continue rotating the door in a clockwise direction. Practice not rotate it counterclockwise until after y'all stop setting it.
5
Turn the unabridged assembly. Carefully and slowly rotate the unabridged assembly in a counterclockwise direction. Proceed turning the assembly until the collar screw faces yous. The door and collar should maintain their alignment as you turn the assembly.^[8]
- Information technology may help you to maintain the position of the collar and door by mark their right positions with a piece of painter'south tape, masking tape, or something like.
6
Tighten the screw to finish adjusting uneven doors. Tighten the collar screw dorsum into its original position. The door should now be properly aligned and stock-still into identify. Give the Lazy Susan a few spins to check that everything works correctly, and your door adjustment is finished.^[9]
- To prevent the neckband from twisting out of place while it's attached, you may need to concur it in place equally the screw is tightened.

Advertising

1
Remove the servant clip to improve acme and bottom clearance. Locate the plastic retainer clip at the lesser of the heart shaft. Firmly grasp the clip between your fingers, open information technology, and pull it out. Under the clip should exist a cutting-out portion of the shaft with a thumbscrew aligning wheel.
- The chiffonier volition need to be completely empty when y'all brand this adjustment. Do not attempt to complete the process when the shelves are loaded, especially if they are heavily loaded.
two
Turn the aligning bicycle. Utilize your fingers to turn the thumbscrew adjustment bike in the cut-out portion of the center shaft. Rotate the wheel clockwise to raise the door and counterclockwise to lower the door.
- Mostly yous tin expect that for each full rotation of the screw the peak will exist adjusted past about 1/32 in (0.8 mm).
- You lot may need to apply gentle pressure to the underside of the lesser shelf to aid the adjustment if you are attempting to raise the door.^[ten]
3
Supercede the retainer clip to complete the pinnacle and bottom aligning. After adjusting the door to the proper elevation, render the retainer clip to its original position at the bottom of the pole. The prune should fasten dorsum into place firmly.^[eleven]
- It's a proficient idea to tighten all of the adjustment screws attached to the heart shaft, shelves, and door after setting the elevation. Doing this could foreclose the door from falling out of alignment over again.
iv
Outline the top and bottom brackets when side clearance is insufficient. Using an erasable pencil, lightly outline the current position of the top and bottom brackets. If lighting is too poor inside the cabinet to brand these marks hands, utilise a flashlight or electrical lantern.
- Doing this will give you a reference indicate to work from as you make the adjustment. Pencil marks can be erased once you lot consummate the process.
5
Realign the pivot pole from the summit. Apply a screwdriver to remove the setscrews and loosen the star washers holding the pivot housing in place on both sides of the pin pole. Adapt the pivot housing and pin pole until both are centered and aligned.^[12]
- When the star washers are in identify but before fastening the setscrews, take a step back and await over your Lazy Susan. If the side clearance is still uneven, remove the washers and readjust the pivot.
- Use your outline to guide your adjustments. For case, if the left side is low, you'll probable need to move the pivot pole and housing to the right.
6
Refasten the pivot housing. Once you tighten the star washers, you'll be set to return the setscrews to their original position. When the screws are in identify, check the side clearance of the Lazy Susan again to make sure that it wasn't altered as you lot refastened its hardware.^[xiii]
- This adjustment may take intendance of your side clearance problem. If the lower one-half of your Susan appears to exist misaligned, you lot'll have to adjust the pivot base in addition to its elevation.
7
Realign the pivot base when necessary. Open the door wide enough to expose the bottom bracket on either side of the Susan. Loosen this subclass by removing the fastening setscrew and star washer with a screwdriver. Now you tin realign the pivot cam (metallic arm) base of operations so that it's centered.^[14]
- You'll have to repeat this process on the opposite side of the Lazy Susan where you'll find an identical subclass/pivot cam base of operations.
- Work on brackets one at a fourth dimension. After you've taken apart, realigned, and refastened the beginning bracket, movement on to the next one.
- When properly centered, the pivot cam bases of both sides should be aligned with regard to the heart pole.
8
Refasten the bracket. Be careful when refastening; if you lot jostle the pivot cam, it could exist knocked out of alignment. Replace the star washers and reattach the setscrews for the bracket. When fastened, similarly suit the opposite side bottom bracket/pivot cam base.
- Verify that the position did not go altered while you were returning these pieces to their original positions by stepping back and evaluating the evenness of the side clearance.
9
Check the door to complete your side clearance adjustment. Sometimes these alignments (particularly those made to pivots) can crave several attempts before they are resolved. Double cheque door alignment later on completing the meridian and bottom adjustments, especially.^[15]
- If the side clearance is still diff, you will need to readjust the peak pin pole and/or bottom pivot cams.

Add New Question

Question

How practice I tighten a Lazy Susan that keeps turning around and around? It won't lock in identify.

There is a plastic clasp at the top of the Lazy Susan. You will see a notch in information technology that should catch then that it holds the unit in place. Commonly, the older units will show the plastic to be worn. Simply supercede the plastic piece, and it should realign and close properly.
Question

What shelf practise I put the heavy items on, summit or lesser?

Putting the heavy items like canned goods on top will increase the chances of the shelf breaking, so put heavy stuff not the bottom instead. The superlative shelf is better for boxes of pasta and bags of rice.
Question

How exercise I gear up set screws that won't tighten?

If the screws for your Lazy Susan don't tighten, the fasteners or the attaching hardware may be stripped. This means that damage has been done to the role of the hardware intended to grip the fastener (similar the grooves of a screw). Supervene upon stripped hardware and try once more.
Question

How tin can I adjust a lesser corner cabinet lazy susan that has the cabinet door attached?

If yous have the one with a cam at the acme of the eye pole and a spiral with a spring, then adjusting the spiral on the side that has a spring on it will conform how the outer surface of the lazy susan "door" aligns with the rest of the cabinets. Don't be agape to tighten all the mode or loosen as far as possible. From what I can tell, the screw will not come out. I turned the screw in and thought I counted the turns. Then backed information technology out once again the same amount of turns and all of a sudden the door was more than than an inch out of alignment. I had to back it out a lot further to reset the alignment.
Question

How do I ready a lazy Susan if the shelf adjuster fell and took the shelf with it? There is not plenty room to conform it and the flange is kleptomaniacal.

If the shelf accommodate fell and knocked a shelf out, damaging the shelf flange, you may need to completely disassemble the shelf, supplant the damaged hardware (inexpensive flanges can be bought at almost hardware stores), and then reinstall the Lazy Susan.

Ask a Question

200 characters left

Include your e-mail address to get a message when this question is answered.

Submit

Thanks for submitting a tip for review!

Things You'll Need

Eraser
Flashlight (or electric lantern for light; optional)
Pencil
Phillips-caput screwdriver
Standard screwdriver
Wrench (or ratchet fix)

About This Article

Commodity Summary X

If yous're having bug with your Lazy Susan, you should be able to accommodate information technology using standard tools. Before you make any adjustments, empty the cupboard so you have infinite to piece of work. If the shelves are stiff when you turn them, loosen the locking bolt at the height of the center shaft with a wrench or ratchet, then motility the adjusting rod an inch, and tighten the bolt. To fix the shelf tiptop, unscrew the locking screws on the central shaft that agree each shelf, adjust the height, so tighten the screws again. If the doors are misaligned, utilize a Philips-head screwdriver to loosen the screw at the pinnacle of the doors, rotate the shelf unit and door counterclockwise until the peak hits the latch, and so rotate the door clockwise until it reaches the center. For more tips, including how to adjust the clearance within your Lazy Susan, read on!

Did this summary help yous?

Thank you to all authors for creating a page that has been read 178,304 times.

Did this article aid you?